Exponent Edge Infinity Bench Review

The Exponent Edge Infinity Bench is a weight bench that combines a flat, incline, and seated weight bench (half bench).

It’s like having 3 benches in one and also has a built-in bulldog pad.

So there’s some unique features in this adjustable bench that give you a lot of bang for your buck.

Let’s check it out!

Unboxing

Everything comes in one box, wrapped in plastic and with plenty of styrofoam around the parts to keep it protected.

There’s not many parts either.

The bottom of the box has the frame and hind leg, and 3 pads on top.

Here’s everything out of the box.

Five pieces in total: frame, back pad, seat pad, head pad, and hind leg.

In case you can’t find the hardware, here’s a heads up.

I looked around the box multiple times until I noticed the hardware was standing up and camouflaged to look like other cardboard flaps.

So make sure you don’t throw away anything until you have the hardware in hand.

Here’s what the Infinity bench looks like after I put it all together.

Assembly was easy since there’s only 5 parts.

Most of it was bolting down the pads to the frame.

Specs

• Dimensions: 50″L x 24″ W x 17″

• Bench weight: 80 lbs

• Flat / incline bench weight capacity: ~ 1000 lbs

• Folding pad weight capacity: 500 lbs

• Seat pad: 14″ at its widest point and 11″ at its narrowest, 2″ thick

• Back pad: 18.5″ x 11″, 2″ thick

• Head pad: 15″ at its widest point and 7″ at its narrowest, 2″ thick

What Is The Exponent Edge Infinity Bench?

The Infinity Bench is a 3-in-1 adjustable bench (flat, incline, and half bench) made by Exponent Edge.

It has a unique design where the back pad folds in half to create a seated weight bench and bulldog pad.

This makes overhead exercises like seated shoulder presses and overhead extensions much more comfortable.

Last time I did seated military press was in a commercial gym where they have half benches specifically for this exercise.

When I use the Infinity bench, I get low back support and have room to lean back a little bit so the bar doesn’t hit my nose.

I can see this being a good fit with the Bulletproof VTS or any dedicated Smith machine.

For the bulldog pad setup, I can use it for chest and back support exercises (so it’s like having the Exponent Edge Infinity Arm built-in to the bench).

Top Benefits Of The Exponent Edge Infinity Bench

Multiple Benches In One

One of the main benefits of the Infinity Bench is that it’s modular so it’s like having multiple benches in one.

It’s a flat bench, incline bench, seated stationary bench, and also works like a bulldog pad.

So if space is an issue in your home or garage gym, and those features fit your exercise program, this bench is a space saver.

Comfortable

As far as comfort goes, the padding in all areas is 2″ thick so it provides good support and feels comfortable.

The vinyl is not like the grip vinyl seen on the Rep Nighthawk bench so that’s something I’d like to see them improve on.

There is a 3″ gap between the seat pad and back pad so if you’re into the no gap benches, this might not be a good fit for you.

I mainly do incline benching so for me this is not big deal.

Space Saving

In my opinion, all benches designed for home gyms should have the ability to stand upright when not in use.

And even though it has a closed ladder system, I like that they added a locking pin to keep the pad from shifting when it’s standing.

Here’s what I mean…

The small arm (arrow 1) on the outside of the ladder flips down and has a hole at the top of it that aligns with a hole on the ladder.

Once those two are aligned, I insert the pin (arrow 2) through the holes and now the angle adjustment arm (arrow 3) is locked in place.

Clever safety design that I haven’t seen in any other adjustable weight bench.

Best Features Of The Exponent Edge Infinity Bench

Folding Head Pad

The folding head pad is what makes the Infinity Bench unique when compared to other adjustable weight benches.

I can flip the head pad down and convert it into a seated weight bench and bulldog pad.

When I’m sitting down, this makes it convenient when doing overhead tricep extensions and seated shoulder presses.

I’ll show you how the folding head piece works…

This is the back of the head pad and in the vertical position it’s held in place by a pin (arrow 2).

When I want to fold the pad down, there’s two brackets (arrow 1) that support the head pad and I can lock it down using the same pin.

The pin pulls out easily and can be inserted from either side.

Once the pin is out, the pad flips down.

Then I insert the pin through the brackets and pad frame to lock it down.

With the bulldog pad setup, I can use it like a seal row bench, hip thrust bench, preacher curl pad, and more.

Here’s how I do seal rows with dumbbells.

I incline the back pad a little bit so it angles the head bad down slightly.

This feels really good with dumbbells but with a barbell I can’t get a full stretch at the bottom.

If I angle the head pad even more, I can use it as a support for hip thrusts.

I just have to make sure the bench is supported on the other because it can slide.

And this is how I do preacher curls…

I incline the seat a bit and angle the head pad down.

The pad is not wide enough to do two arms at a time but for single dumbbell curls it works great.

Incline Bench

The bench has 8 back pad angles and 5 seat angles, no decline.

They go from flat to 90 degrees.

It uses a closed ladder system which I like because it makes it safer than an open ladder when standing upright.

One thing I’d like to see, is angles etched or laser cut into the ladder so it’s easier to know where I’m at.

One unique feature that this bench has, is a small flip down arm (arrow 1) that locks the bench pad in place so it doesn’t move when it’s stored.

The arm has a hole that matches a hole on the ladder.

After I lower the support arm, I insert the pin (arrow 2) through the holes and the support arm is pinned down.

The seat has 5 angle adjustments starting with flat and 4 incline adjustments.

I adjust the seat with a simple pop pin.

And here’s what the seat pad looks like when it’s fully inclined.

The seat pad hovers just above the bottom back pad and that’s the reason there is a 3″ gap in the flat bench position.

Here’s what it looks like when I’m incline pressing.

It’s comfortable and doesn’t wobble since most of the weight is spread out over the width of the hind legs.

Flat Bench

And the other setup is the flat bench.

I hear people talk about how they fall into benches with big gaps but I don’t see how.

You can see my shirt falls into the gap but my butt and back are always supported.

My butt is on the seat pad, my lower back curve hovers over the gap, and my middle back is supported by the back pad.

Edge Infinity Bench Pros & Cons

Pros

• 3-in-1: It’s a flat bench, incline bench, and seated weight bench

• Folding head pad: I can use the folding head pad as a bulldog pad for back and chest supported exercises

• Vertical storage: Upright storage is always helpful to save floor space

• Padding: 2″ padding is comfortable and supportive

• Versatility: I can do exercises not normally seen with an adjustable weight bench

Cons

• Angles: I’d love to see angles etched or laser cut into the ladder so it makes it easier to know where I’m at

• Gap: There’s a 3″ gap between the seat pad and back pad which some people may not like. Personally it doesn’t affect me.

Exponent Edge Infinity Bench Price

The price for the Edge Infinity Bench is $549.

Not the most budget friendly bench but it’s replacing 3 benches and a bulldog pad so there is a lot of value in this space saving design.

But I’ll just show you how to bring the price down some…

Exponent Edge Discount Code

If you’re looking for an Exponent Edge discount code, you’re in luck because this will knock off 5% from any product on their website.

Just click the red button below to reveal the 5% discount code.

Exponent Edge Infinity Bench Alternatives

Freak Athlete ABX Adjustable Bench

The Freak Athlete ABX adjustable bench is similar to the Infinity bench because Freak Athlete collaborated with Exponent Edge.

They borrowed the flip down back pad idea plus they added a few more details.

Freak Athlete’s ABX has the ability to add attachments: dip station, ab attachment, and leg developer.

Plus it comes with an automatic zero gap adjustment and TruGrip vinyl.

RitFit 3 Section Weight Bench

This RitFit 3 Section adjustable weight bench works in a similar way as the Edge Infinity bench.

I like that they added angles on the ladders so I can see what angles I use and it has decline settings for those who like to decline bench.

But based on a few reviews I’ve read, the craftsmanship is not all that good.

Mikolo Bastet 2.0 Adjustable Bench

The Mikolo Bastet 2.0 adjustable bench is a flat, incline, decline, and half bench.

So it’s 4 benches in 1 plus it adds the bulldog pad feature.

It’s built with 3×3″, 14-gauge steel, and has laser cut numbering in a closed ladder system.

My Experience Using The Exponent Edge Infinity Bench

I own the Exponent Edge Infinity Arm rack attachment so having something similar to it built-in to a bench is very convenient.

There’s nothing to attach or remove from my rack and don’t need any extra space to store the attachment when I’m not using it.

Now that I own the bench, I get more use out of it then other benches I currently have because the flip down pad gives it another dimension.

And I’ve brought back seated military presses from the dead with that shoulder room I get from the half bench.

Is The Edge Infinity Bench Worth It?

If you’re looking to save space and a bench that has several benches built-in to one, this is a good option.

It works as a flat bench, incline bench, seated weight bench, bulldog pad, preacher curl bench, hip thrust bench, and more…

Function wise, I can get a lot of exercises done on it in a small footprint and it also stores vertically so it’s out of the way when not in use.